The ADR-818 Eight-Channelis an Input Module, 2- or 3-wire connection. 3-wire connections are used when connecting detectors that require relatively high current such as gas detectors

ADR-823 Three-Channel Input/Output Module, supervised input and outputs

ADR-828 Eight-Channel Output Module, unsupervised outputs

The ADR-828 enables activation of 8 unsupervised outputs for auxiliary indications only. It is used for synoptic panels, indication lights, directing signs, relays, etc. The output can drive 24 VDC lamps or LEDs.

The ADR-812 is a two-IDC monitor module that operates as an interface between the ADR-3000 analog addressable control panel and compatible two-wire conventional initiating devices or switches. The ADR-812 has
 a 24 VDC resettable power limited output. This output is interrupted on Reset, in order to reset devices that were latched on alarm. This 3 or 4 wire arrangement enables connection of detectors with higher power consumption.

The LI-3000 Analog Addressable Line Isolation Module provides the SLC loop with advanced capability of protection from fault conditions such as short- and open circuit, enabling continuous operation of the loop by isolating the faulty section from the rest of the loop.

Industrial installations may have strong electromagnetic interferences. In order to isolate and protect the SLC loops and 24 VDC outputs from electromagnetic interference install Telefire's EPI-3000 Electromagnetic and Surge Protection Interface Module. One EPI-3000 module will isolate all four loops, and both 24 VDC outputs (24V_A and 24V_B) of a single ADR-3000 fire alarm control panel.

TFH-220F - conventional fixed temperature heat detector.

TFH-220A - combined Rate of Rise and Fixed Temperature for Telefir's analog addressable systems.

Airflow in ventilation ducts is far too fast for smoke detectors. The DTH-400 is the solution to this problem. Installation of the detector in a box with a special device slows the airflow across the detector.

There are many instances where high sensitivity, aspirated type smoke detection systems are "specified". The Laser Aspirated Smoke Detector, (LASD), from Fire Fighting Enterprises Ltd provides the perfect high sensitivity smoke detection solution. A high performance aspirator and flow monitoring circuit ensure a constant, monitored flow level, which can be

displayed on a 10 element bar graph with adjustments for high and low flow thresholds. Three alarm levels give warnings at their pre-set levels.

The system comprises of a single unit incorporating an infra- red Transmitter
and Receiver. The signal is reflected by a prism and analysed for smoke presence. The system comprises Single Compact Housing and Available in 50 metre or 100 metre Version.

Reflective optical beam smoke detector with a motorised head, that can align itself when commissioning, and continually correct itself against building movement. This detector can also be controlled and adjusted from ground level.

TPB-10R Indoor Manual Fire Alarm Call Point- (red) 
TPB-10Y Indoor Manual Extinguishing Call Point- (yellow)
TPB-800ASR - analog addressable call point. It consists of a standard alarm call point unit and an analog addressable interface module.
The TPB-800ASY - analog addressable extinguishing push-button. It is mechanically and electronically identical to the TPB-800ASR, with the exception of its color.

Telefire's TIP-224 is a conventional indoor syren with a bright LED. The TIP-224 can be connected to the NAC (Notification Alarm Circuit) output.

TFS-4460 / TFS-4484 Alarm Notification Sounder - Outdoor (with or without strobe)

The TPS-34A is an external power supply that is fed from a 230 VAC source input and includes a 24 VDC 4 A power supply, battery charger, and a control card that monitors the TPS-34A and reports status and trouble information to the ADR-3000 Analog Addressable Control Panel. It is used when the total demand on the ADR-3000's 24 VDC power supply exceeds its capacity, or to power I/O modules, sounders, or special detectors that are installed a long distance away from the control panel.

Telefire's TDM-500i Intelligent Dialer is intended for use in fire, security and safety  systems to call automatically dial and play pre-recorded voice messages on alarm and trouble events to emergency services and key personnel. The TDM-500i is available in two configurations:
TDM-500i  the standard version that uses
24 VDC sourse. TDM-500i/12  an optional version that uses 12 VDC sourse.

The RM-4005 Remote Panel and Annunciator enables control and supervision of the ADR-3000 Fire Alarm Control Panel from remote locations and key positions such as: security officer, premises manager, or maintenance office.

The RM-4005 Remote Panel consists of an LCD display, keypad, internal buzzer, and features such as alarm output, trouble output, and an interface relay that diminishes the need for additional input/output interface cards.

In large scale systems incorporating several control panels connected via a peer-to-peer network, up to 16 remote panels can be connected to each of the control panels.

The TDA-1000 is used as a remote display unit for the GSA-1000 conventional fire alarm control panel. It will display all events occurring.

The TCS-3040 (Telefire Control Software) is a powerful interface tool that enables the monitoring of the control panel and performing general tasks such as remote project programming using the PC.
The TCS-3040 can use the PC's modem to connect remotely via a phone line to the ADR-3000 using the optional MCID-34 modem.If the ADR-3000 is equipped with Telefire's NET-3000 module, the TCS-3040 can perform the same function over TCP/IP via the organization's intranet or over the Internet if such a connection exists.

The MCS-3000 Centralized Fire Alarm Systems Monitoring Software is a Microsoft Windows™-based software that monitors fire alarm systems equipped with the NET-3000 Internet Enabled Monitoring and Notification Module.
The MCS-3000 constantly scans over the LAN / WAN all configured panels, allowing the monitoring of multiple fire alarm control panels, using a single screen that concentrates the whole systems status including normal operation, alarm and trouble.

The PROG-4000 is a tool for programming and testing all of Telefire's analog addressable devices such as detectors, manual fire alarm call points, input modules, output modules, remote power-supplies, etc.

The TFR-900 is a telescopic rod that can extend up to 4.50 m and has a head mechanism to ease the task of inserting or removing detectors from their base without the use of a ladder. The head mechanism contains a powerful magnet that can be used to test Telefire's detectors.